Dish installing network satellite

Connect a temporary cable to a peaking meter. Thread the other end of the cable through the LNBF arm and bracket. Attach the LNBFs to the bracket using the included screws. Do not adjust the skew. Ensure you are peaking the dish using transponder 11 or higher. With the peaking meter still connected, tighten the mast clamp and elevation bolts using the torque values listed in Table 1 on page 6. Re-confirm signal strength after tightening the bolts. Remove the temporary cable used for peaking the dish.

Thread the cable s from the receiver s through the LNBF arm and bracket. Connect a cable from DPP If a Legacy receiver is present, it should be installed last. Connect a cable from the DPP A splitter or other device will not work in this configuration.

If you use a wrench, you may over-tighten the connections and damage your equipment Connect the receiver s to the TV s and display the Point Dish screen if not shown, for most receivers, press MENU on the remote control.

Join Our Mailing List. Email Address:. Website design by Solid Cactus. The dish must have a clear line of sight to the satellite. Even dense cloud or heavy rain will reduce the signal to some degree and the branches of a tree can kill it altogether.

It would not work through a skylight either. Not Helpful 2 Helpful 4. Free to air services do not need a landline. Most modern contract satellite receivers will use an Internet connection and you can get routers that work with mobile phone networks.

Not Helpful 2 Helpful 2. Paul Cinker. Not Helpful 1 Helpful 1. No, receiving aerials are tuned to work with different frequencies and satellite transmissions are completely outside the range of terrestrial broadcasts. There are different types of TV aerials and even using the wrong one reduces the signal. Not Helpful 4 Helpful 0. How do I cover the eye of the Dish Network satellite when it rains and I lose signal? Your problem could be due to water seeping into either the F-connectors or the LMB itself.

I live on the east coast of Ireland. I have not had the need to cover any part of the dish LMB, etc. However, when I was connecting to the LMB, I coated the threads where they connect to the cables with petroleum jelly to seal the connection.

I also put down insulating tape around the F-connector. Not Helpful 0 Helpful 0. This will depend on what setup you have. Take a look at TV. IE, where you will find a huge resource of tutorials. Let us match you with a local satellite dish installer. The satellite installers in our network are more than just electrical contractors. These hardworking folks are our partners. We proud to recommend any and all of our local satellite installers. You can trust them to do a great job, too!

Make sure the bolts are level with the wall, or else the dish's mount won't anchor properly. Place the metal plugs and hammer them into the wall.

Your dish will come with a set of plugs that serve as wall anchors. Position them, so their open end faces out from the wall. That opening is for bolting the wall mount in place. After pushing the plugs into the holes, tap them in with a hammer and chisel. They are what anchors the mount to the wall or ceiling.

If they are loose, your dish could end up crashing to the ground! Bolt the mount onto the plugs in the wall. Position the mount back on the wall, lining up the plate's holes with the pilot holes you drilled. Fasten the bolts by using a cordless screwdriver.

Make sure the mount feels secure in the wall before you move on. If you're sure they are in correctly, take them out and recheck the plugs. Cap each bolt with a metal washer and locking nut. These components prevent the bolts from coming back out of the wall. Slide the washers on first, which are flat metal disks that help the nuts work properly.

Then, add the nuts and turn them clockwise with a wrench until they feel tight and no longer move. Be careful not to overtighten the nuts. Stop twisting them when they become hard to move. As long as they are not loose, the mount will also stay in place.

Part 2. Attach the antenna bracket to the low noise block LNB arm. Your dish will most likely come with a flat metal plate to connect the satellite dish to the L-shaped LNB arm and other components. Position the plate, so the prongs are on the left and right, facing you. Hold the LNB arm between the prongs with the tail end extending out past the plate's opposite side. The exact installation process, including the bolts' size, may vary a little depending on the dish you have.

Refer to the owner's manual for more specific instructions. Clip the antenna adjustment panel over the plate's prongs. The panel will look like a square box with one end open. Add a washer and nut on the end of each bolt after tightening them.

This slot is what you use to point the satellite up or down. Fit the U-shaped rod inside the adjustment panel. Your dish will have a bent metal rod that fits into one of the slots on the adjustment panel.

Slip the rod inside, sliding its prongs through the holes. Ensure the prongs point toward you rather than the tail end of the LNB rod you connected earlier. Fit a small clamp over it, followed by a washer and nut on each prong. The adjustment panel has 3 different slots. Use the slots to reposition the satellite dish. In most cases, the middle slot is best for setting the dish at the proper angle. Bolt the antenna bracket to the back of the satellite dish.

You have a couple more bolts to add to finish the bulk of the assembly, and this is one of the easiest parts to finish. Line up the holes on the plate with the holes on the back of the dish. Stick the longest bolts you have, usually 2 to 3 in 5. Then, place a washer and nut on the end of each bolt, tightening it with your wrench.

If they feel shaky, carefully separate them and tighten the bolts. One last component, the LNB, controls the dish's functionality. First, slide the handle of the LNB onto the open end of the arm. Secure it with nuts and bolts, then take the LNB out of the box. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality.

Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support. If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together.

If the dish looks good, then you're ready to position it to communicate with a satellite.